Jovie/da

KDE's tekst til tale-system, KTTS

Hovedtræk

• Konverterer tekst til lyd
• Meget konfigurerbar
  • Erstat fejludtalte ord
  • Vælg talesynthesizere
  • Konfigurer lyd-output
  • Håndter jobs
• Kører i systembakken
• Integrerer med de fleste af KDE's applikationer
  • Oplæser tekst fra klippebordet
  • Oplæser hele tekstfiler eller udvalgte udsnit i Kate
  • Oplæser hele HTML-sider eller udvalgte udsnit i Konqueror
  • Kan bruges til bekendtgørelser (KNotify)

Beskrivelse

KDEs tekst til tale-system KTTS er en applikation, som kører i baggrunden for at oplæse tekst over hele skrivebordet. Det integrerer med mange applikationer og er enkelt at bruge.

Opsætning

Efter installation kan du starte KTTS ved at vælge kttsmgr i startmenuen under Værktøjer; eller du kan starte KRunner (Alt+F2) og skrive

kttsmgr

. Du skal først sætte KTTS op før du kan bruge dets talesyntetisering.

Note

Du kan også konfigurere KTTS fra Systemindstillinger

Første skridt er at sikre dig, at du har en kompatibel tale-generator installeret. Følgende synthesizere er kompatible med KTTS: Festival, Festival Lite (flite), Hadifix, Epos, og FreeTTS. Enhver generator, som kan køres fra kommandolinjen kan også bruges med KTTS.

Nu kan du fortsætte med at lave en oplæser. Vælg fanebladet Oplæsere i kontrolmodulet Tekst-til-tale og klik Tilføj.

Vælg sprog og hvilken synthesizer, du vil bruge. For at bruge Festival skal du have en stemme installeret; du kan konfigurere dette bagefter ved at klikke på knappen Redigér. KTTS' skulle nu være klar. Test det ved at vælge </menuchoice>Rediger -> Test</menuchoice>.

Konfiguration

For at indstille talerens stemme, volumen, hastighed og stemmeleje går du til fanebladet Oplæsere, vælger oplæseren og klikker på Rediger. Et vindue som det ovenfor dukker nu op; her kan du indstille oplæseren. For at kunne ændre stemmen skal du have andre stemmer installeret.

Hvordan man bruger KTTS

Systembakken

If enabled in the configuration, KTTS will be availabe to you in the System Tray. Right-clicking it will reveal the menu which is straight forward and allows for control of the speech output.

Notice the Speak Clipboard Contents in the menu, if the application isn't integrated with KTTS (Read more about the applications with KTTS built-in in the next section) you can copy the text you want spoken, and click Speak Clipboard Contents to hear it read.

Integration with other Desktop Applications

Konqueror

KTTS allows you to speak the text on a web page. In the menu go to Tools -> Speak Text. However you may not want to do this because it will also read the HTML headers on the page. Instead highlight the text you want spoken and then select Speak Text.

Also note this feature is built into Okular as well. In the Tools menu you will be give two choices Speak Whole Document or Speak Current Page.

Notifications

KTTS works with any application that uses notifications. To set this up start an application such as Konversation that uses notifications. In the menu go to Settings -> Configure Notifications...

As you can see you can have various notifications for different events, such as when someone triggers a highlight. By selecting it to speak for this event it will notify you through audio output each time this event happens. Of course you can also have more than one notification.

If an application doesn't include the ability to speak text remember that you can always highlight and copy text and then use KTTS to speak your clipboard contents.

For more information check out the KTTS Handbook included with KTTS.

KTTS was renamed to Jovie during 4.5 release cycle. Thus, if you cannot find ktts package in your distribution just install Jovie.

For more information please refer to Jovie handbook.